QUESTION 95
Refer to the exhibit. The EEM script is applied in the default VDC to collect the outputs during high CPU utilization on the Cisco Nexus 7000 Series Switch for all VDCs.
Which configuration set must be added to the script to fix the issue?
A.switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1
switch(config-apple)# action 0.2 cli enable
switch(config-apple)# action 0.5 cli switchto vdc Core
switch(config-apple)# action 0.8 cli switchto vdc Distribution
B.switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1
switch(config-apple)# action 0.2 cli enable
switch(config-apple)# action 0.5 cli switchto vdc Core
switch(config-apple)# action 0.8 cli switchto vdc Distribution
C.switch(config-apple)# event snmp oid 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1
switch(config-apple)# action 0.2 cli config t
switch(config-apple)# action 0.5 cli switchto vdc Core
switch(config-apple)# action 0.8 cli switchto vdc Distribution
D.switch(config-apple)# event snmp 1.3.6.1.4.1.9.9.109.1.1.1.1.6.1 get-type exact entry-op ge entry-val 50 poll-interval 1
switch(config-apple)# action 0.2 cli config t
switch(config-apple)# action 0.5 cli switchto vdc Core
switch(config-apple)# action 0.8 cli switchto vdc Distribution
Answer: B
QUESTION 96
Refer to the exhibit. An engineer troubleshoots the HSRP configuration and notes that the remote end uses HSRP version 1. The engineer sets the local HSRP to version 1, but the problem continues. Which action resolves the issue?
A.Change the local group number to 255 or less and request that the remote data center matches the group member in its configuration.
B.Set the local group number as 300 in the remote data center configuration
C.Run version 1 and version 2 HSRP on VLAN300 in the local data center.
D.Reduce the priority of the local HSRP to below 100 to force the local HSRP to standby and then change the version to version 1.
Answer: A
QUESTION 97
An engineer must upgrade all components in a Cisco UCS domain to the same package version, but the upgrade process fails to complete.
Which set of Auto Install actions resolves the problem?
A.Install Infrastructure Firmware, then Install Server Firmware.
B.Install infrastructure Firmware, then Install Hypervisor Firmware.
C.Install Hypervisor Firmware, then Install Infrastructure Firmware
D.Install Server Firmware, then Install Infrastructure Firmware
Answer: A
QUESTION 98
A Cisco UCSB-Series Blade Server is configured to boot a VMwareESXi host from an EMC VNX storage array by using a Fibre Channel SAN. The boot order is confirmed to be configured as expected but the server fails to boot from the SAN. Which action reserves the problem?
A.Set the same WWPN pools for vHBA adapters
B.Set the boot LUN to the highest LUN ID in the storage array
C.Set the boot LUN to the lowest LUN ID in the storage array
D.Set the same WWNN pools for vHBA adaptor
Answer: C
QUESTION 99
Refer to the Exhibit. An Engineer cannot log in to the Cisco IMC page of the Cisco UCS C220 server. Which action resolve the issue?
A.Se the FQDN of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.
B.Use the DNS of the Cisco IMC webpage login page instead of the IP address for the connection to be secure.
C.Replace the self-signed certificate that is installed on the Cisco IMC with a server certificate that is signed from the client corporate certificate.
D.Replace the self-signed certificate that is installed on the Cisco IMC with a user certificate that is signed from the client corporate certificate.
Answer: C
QUESTION 100
An engineer must place a Cisco UCS B-Series Server in a single server pool in Cisco UCS Manager.
The engineer creates a qualification policy, but the server is still seen in multiple pools.
Which two actions resolve the issue? (Choose two.)
A.Select the Server Pool Policy Qualification from the qualification drop-down menu in the Server Pool Policy
B.Select the Server Pool Policy from the qualification drop-down menu in the Server Pool Policy Qualification
C.Set the operating system qualifier inside the Server Pool Policy Qualification
D.Set the number of vNICs qualifier inside the Server Pool Policy.
E.Set the storage capacity qualifier inside the Server Poo. Policy Qualification.
Answer: AC
QUESTION 101
Refer to the exhibit. A network engineer traces the packet flow from the Veth991 of a blade server toward the core switch. The switch reports performance issues.
What is the role of the interface Eth1/7?
A.IOM network interface
B.fabric interconnect uplink interface
C.IOM host interface
D.server interface
Answer: B
QUESTION 102
Refer to the exhibit. A PC belongs to VLAN 68. The user experiences a large amount of packet loss when communicating with hosts that are outside of VLAN 68.
Which action resolves the problem?
A.Replace HSRP with GLBP
B.Enable the peer-gateway feature
C.Remove the HSRP configuration
D.Configure ip arp synchronization on both switches.
Answer: B
QUESTION 103
A customer reports that the Chassis Management Controller fails to receive chassis information from Cisco UCS Manager. Which set of steps resolves the issue?
A.1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status
4) Reseat the affected IOM.
B.1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status
4) Reseat the affected IOM.
C.1) Verify that the IOM firmware and Cisco UCS Manager are at the same software level.
2) Verify that at least two physical cables between the IOM and fabric interconnect function properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.
D.1) Verify that the IOM firmware and Cisco UCS Manager are at different software levels.
2) Verify that at least one physical cable between the IOM and fabric interconnect functions properly.
3) Check for runtime link down status.
4) Reseat the affected IOM.
Answer: B
QUESTION 104
Refer to the exhibit. During implementation of a Cisco UCS C-Series Server, an engineer receives the status that is shown in the exhibit. Which action resolves the issue?
A.Reconfigure the Drive Type from "Removable" to "Non-Removable"
B.Insert an SD card into SLOT-2
C.Configure the RAID that is associated with the card.
D.Set SLOT-1 Sync Mode to "Auto"
Answer: A
QUESTION 105
A system administrator adds two vNICs to an existing service profile that is used to run a vSphere environment to support disjoint Layer 2 network connectivity.
However, after the server is rebooted, the host is not accessible on the network. Which action resolves the issue?
A.Remove all existing vNICs and add them in the desired order.
B.Build a new service profile with the desired network configuration
C.Add the disjoint Layer 2 VLANs to an existing vNIC rather than adding new vNICs
D.Create a vNIC placement policy to avoid adapter renumbering
Answer: C
QUESTION 106
Refer to the exhibit. An engineer deploys SAN environment with two interconnected Cisco MDS 9000 Series switches.
When the engineer attempts a zone merge, it fails with the error that is presented in the exhibit. Which action resolves the issue?
A.Import or export a zone set between the switches to synchronize the switches.
B.Change the name of one of the zones to match the other zone set.
C.Set the distribute policy of the zone to full.
D.Ensure that the zone members have different names.
Answer: A
QUESTION 107
Refer to the exhibit. One of the vPC VTEPs fails to route VXLAN traffic to vPC connected hosts. When the issue was being diagnosed, it was discovered that the packets that were expected to be forwarded to the MAC address on the SWITCH-VTEP-1 are instead forwarded to the MAC address on SWITCH-VTEP-2 and then dropped. Which action resolves the issue?
A.Configure a distributed anycast gateway on both peers
B.Configure ip arp synchronize under the VPC domain on both peers
C.Configure peer-gateway under the VPC domain on both peers
D.Configure a different secondary IP address for one of the vPC peers
Answer: C
QUESTION 108
Refer to the exhibit. An engineer troubleshoots an OSPF neighborship problem between Router R2 and Router R10. Which action resolves the problem?
A.Change area ID on Router R10
B.Resolve unicast reply from Router R2
C.Resolve authentication type on Router R10
D.Change router ID on Router R10
Answer: B
QUESTION 109
Refer to the exhibit. VSAN traffic is not routed as expected. Which action should be taken to resolve the issue?
A.Reset the error packet counter
B.Configure the hello timer to match the neighbor
C.Configure the FSPF dead interval with a value higher than 80 seconds
D.Reset the inactivity timer on switch-2
Answer: B
QUESTION 110
Refer to the exhibit. A network engineer configures an authentication domain through an LDAP provider on the Cisco UCS Manager for users from different companies to log into their respective organizations created in the UCS Manager. The engineer tests the configuration and notices that any user has login access to any organization in the UCS Manager. Which action should be taken to resolve the issue?
A.Configure the Filter field with sAMAccountName=$company
B.Configure the Attribute field with the company
C.Configure the Attribute field with sAMAccountName=$company
D.Configure the Filter field with the company
Answer: A
QUESTION 111
A network engineer is implementing the Cisco ACI Fabric and notices that the Leaf-1 switch is registered, has an assigned name, but is displayed as inactive in the APIC. After further investigation, it became clear that the leaf switch was recently moved from another Cisco ACI environment. Which action resolves the problem?
A.Clean reload the Leaf-1 switch
B.Define the new TEP address for Leaf-1
C.Change the clock offset from low to high between apic 1 and Leaf-1
D.Modify the ISIS interface peering IP address between apic 1 and Leaf-1
Answer: B
QUESTION 112
A system administrator connects a Cisco Nexus 2248PQ FEX to a fabric interconnect to expand the ports that are available for connecting Cisco UCS C-Series Rack Servers. In Cisco UCS Manager, the administrator does not see the servers connected to this FEX. Which action should be taken to resolve the issue?
A.The FEX must be exchanged so that it supports the connectivity between fabric interconnects and UCS Cseries servers
B.The fabric interconnects must be rebooted before the FEX is recognized
C.The transceivers must be exchanged to support the connectivity between the FEX and the fabric interconnects
D.The ports that connect the FEX to the fabric interconnects must be configured as server ports
Answer: D
QUESTION 113
Refer to the exhibit. An engineer discovered a VFC interface in a down state on a Cisco Nexus Switch. Which action resolves the problem?
A.Change the cable between the switch and the server
B.Reset the Cisco Nexus port toward the file server
C.Update the CNA firmware and driver versions
D.Modify the fip keepalive message time to 30 seconds
Answer: D
QUESTION 114
Refer to the exhibit. A network engineer is configuring the FCoE N_Port virtualization storage area network. After the initial implementation, server 11 fails to connect to the disk array. Which action resolves the issue?
A.On MDS interface vfc 1/1, change switchport mode configuration to VF
B.On N9K interface vfc11, change switchport mode configuration to NP
C.On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to F
D.On N9K interface vfc11 and MDS interface vfc 1/1, change switchport mode configuration to E
Answer: D
QUESTION 115
Refer to the exhibits. An engineer is implementing the SAN based on the Cisco MDS 9000 Series Switches. When operating the environment, the engineer encounters the error shown. Which action resolves the issue?
A.Copy VSAN 101 to the fabric binding database on the MDS-1 switch
B.Add the World Wide Name of the neighboring switch to the MDS-1 switch
C.Configure the port security feature on the MDS-1 switch
D.Enable VSAN 101 on the peer MDS 2 switch fabric interconnect
Answer: B
2023 Latest Braindump2go 300-615 PDF and 300-615 VCE Dumps Free Share:
